500-2060 Power Take Off Adapters - 460 Ford 1310 Flexplate
Uses 3/8-24 bolts on 2" x 2-3/8" centers
These flanges bolt on the flywheel and accept 1310 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2065 Power Take Off Adapters - 460 Ford 1350 Flexplate
Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
These flanges bolt on the flywheel and accept 1350 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2020 Power Take Off Adapters - Chevy 1310 Flexplate
Uses 3/8-24 bolts on 2" x 2-3/8" centers
Fits Small Block Chevy with a two piece rear main seal and all Big Block Chevy . These flanges bolt on the flexplate and accept 1310 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2025 Power Take Off Adapters - Chevy 1310 Flywheel
Uses 3/8-24 bolts on 2" x 2-3/8" centers
Fits Small Block Chevy and Big Block Chevy with a two piece rear main seal. These flanges bolt on the flywheel and accept 1310 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2050 Power Take Off Adapter - SBC 1350 Flexplate Post-1987, 1-pc Rear Seal
These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2040 Power Take Off Adapters - Small Block Chevy 1310 Flexplate 1987 and newer, 1 PC rear seal
Uses 3/8-24 bolts on 2" x 2-3/8" centers
These flanges bolt on the flywheel and accept 1310 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2045 Power Take Off Adapters - Small Block Chevy 1310 Flywheel 1987 and newer, 1 PC rear seal
Uses 3/8-24 bolts on 2" x 2-3/8" centers
These flanges bolt on the flywheel and accept 1310 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2030 Power Take Off Adapters - Small Block, Big Block Chevy 1350 Flexplate
Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
These flanges bolt on the flywheel and accept 1350 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2035 Power Take Off Adapters - Small Block, Big Block Chevy 1350 Flywheel
Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
These flanges bolt on the flywheel and accept 1350 spicer drivelines. There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.
Need help choosing your new PTO flange? Check out this handy tutorial!
|
|
500-2150 PTO 1310 Adapter Bolt Kit
Note: To determine U joint flange size (1310 or 1350) refer to the followinginformation.
1310 - uses 3/8-24 bolts on 2" x 2-3/8" centers
1350 - uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
Contains (6) 7/16" x 1-1/4" Bolts and (4) 3/8" x 1" bolts
NOTE: This bolt kit does NOT fit LS PTO's, for LS PTO bolts CLICK HERE.
|
|
500-2154 PTO 1310 Adapter Bolt Kit For SB Chevy
Note: To determine U joint flange size (1310 or 1350) refer to the followinginformation.
1310 - uses 3/8-24 bolts on 2" x 2-3/8" centers
1350 - uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
For use on newer model SB Chevy PTO's with 1 pc rear seal
Contains (4) 7/16" x 1-1/4" Bolts and (4) 3/8"x1" bolts
|
|
500-2152 PTO 1350 Adapters Bolt Kit
Note: To determine U joint flange size (1310 or 1350) refer to the following information.
1310 - uses 3/8-24 bolts on 2" x 2-3/8" centers
1350 - uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers
Contains (6) 7/16 x 1-1/4" Bolts and (4) 7/16" x 1" bolts
|
|
620-4620 Replacement M66 Rotary Steering Cable (Steering Wheel & Helm Not Included)
Features and Technical Specifications:
- Click here for how to measure for replacement cable
- Cable Entry can be set from either Port or Starboard sides
- Fast connect, simple installation
- All stainless steel cable output ends
- Corrosion resistant materials
- Particularly suitable where clearance is limited
- Minimum steering cable bend radius: 7.9” (200 mm)
- Minimal feedback
- Compact for mounting
- Exceeds EN 28848 safety standards
- Exceeds ABYC P17 safety standards
- Replaces Morse Command 290 Cables (300962, 304411 or 312020)
- Replaces Teleflex SS62 Cables
- Replaces Teleflex SS72 Cables (K66 Installation kit needed)
|
|
620-3620 Replacement M86 Rack and Pinion Steering Cable (Helm Not Included)
Featuresand Technical Specifications:
- Click here for how to measure for replacement cable
- All stainless steel cable output ends
- Made exclusively in corrosion resistant materials
- Minimum steering cable bend radius: 7,9” (200 mm)
- Exceeds EN 28848 safety standards
- Exceeds ABYC P17 safety standards
- Replaces Morse Command 200 Cables (E300619 & E300620)
- Replaces Telflex SS124 Cables only
|
|
620-103112 "SE" Sport Edition Loader Scoop for Berkeley JG, JC, JI, & Dominator Pumps
This is the all "SE" Sport Edition loader scoop from
Hardin Marine. These loader scoops are a great entry level
upgrade from a stock jet intake grate. They are designed to work
best with stock or only mildly modified engine packages. By
using an outer angle ramp design this unit can help to deliver
more water into the jet intake for improved performance.
|
|
950-758800 Splined Pump Shaft Socket
This special wrench fits over the splined end of the pump shaft enabling you
to easily hold the shaft while tightening or loosening the impeller nut - 1/2"
square drive fits all common tools.
|
|
620-103113 "SS" Super Sport Loader Scoop for JC, JG, JI Pumps
This is a fabulous loader scoop. With virtually hundreds
of hours of research and development Hardin Marine has
come up with the new "SS" Super Sport loader scoop. This unit
is designed for the performance jet boat enthusiast with 375
to 500 horsepower. The long inlet ramp design forces water
to the top of the impeller where it's needed, to load your
jet pump for maximum thrust efficiency.
|
|
620-103114 "SS" Super Sport Loader Scoop for JE & JF Pumps
This is a fabulous loader scoop. With virtually hundreds
of hours of research and development Hardin Marine has
come up with the new "SS" Super Sport loader scoop. This unit
is designed for the performance jet boat enthusiast with 500 + horsepower. The long inlet ramp design forces water
to the top of the impeller where it's needed, to load your
jet pump for maximum thrust efficiency.
|
|
950-758300 Suction Seal Driver
This new jet pump seal & bushing driver simplifies the installation process
of critical bowl bushings and various seals in the jet pump. The stainless
driver shaft is threaded and interchangeable with all the drivers.
|
|
620-370618
Swivel Connection Kit, Billet Aluminum
Used with the steering cable on a jet boat to connect to the steering arm.
|
|
500-0513 Stainless T-Handle Twist-In Drain Plug
We carry all of the popular twist-in drain plugs from original aluminum drain
plugs to stainless and brass plugs. This plug is stainless steel and does not include a chain or cable.
|
|
150-S15380 Three Point Bellhousing Strap
Replacement Strap for the 3 point bellhousing.
center to center measurment: 6-3/8"
|
|
This Part has options, please click the button below to order.
620-3090 + Option(s) Uflex Rack and Pinion Steering System Packaged in a Box
A convenient kit form, especially suitable as replacement steering, that includes helm, bezel and cable. The cable is available in 1-ft increments from 8 to 20 feet (specify cable length when ordering). The wheel is not included. Click here for how to measure for replacement cable.
This kit includes:
- M86 - pre assembled helm with steering cable
- G86 - shaft assembly
- X34 - 90° bezel (diameter is 5 1/8")
Features and Technical Specifications:
- All stainless steel cable output ends
- Made exclusively in corrosion resistant materials
- Optional 90° or 20° installation
- Standard 3/4”tapered shaft
- Lock-to-lock steering wheel turns: 3,5
- Stroke: 8.2” (210 mm)
- Maximum allowable steering wheel diameter: 16.5” (420 mm)
- Minimum steering cable bend radius: 7,9” (200 mm)
- G86 steering systems are not to be used on boats equipped with engines that exceed the maximum horsepower rating of the boat
- Exceeds EN 28848 safety standards
- Exceeds ABYC P17 safety standards
|
|
620-3080 Uflex Rotary Steering System Packaged in a Box
A convenient kit form, especially suitable as replacement steering, that
includes helm, bezel and cable. The cable is available in 1-ft increments from 8
to 20 feet (specify cable length when ordering). Featuring the T71FC helm with a Planetary Gear Design, the Rotech
reduces steering effort and delivers more balanced loads on the steering
wheel. This unique design also offers a wider wear area which reduces
lost motion and improves durability. Centered on the main drive shaft,
this helm requires less room behind the dash and is a direct “drop in”
replacement for competing system; requiring no new holes for
installation. The Rotech package also includes the M66
universal Rotary Steering Cable with stainless steel output fittings for
maximum longevity and smooth steering. Click here for how to measure for replacement cable.
This kit includes:
- T71FC - helm
- X34 - 90° bezel (diameter is 5 1/8")
- M66 - steering cable
Features and Technical Specifications:
- Cable Entry can be set from either Port or Starboard sides
- Fast connect, simple installation
- All stainless steel cable output ends
- Corrosion resistant materials
- Particularly suitable where clearance is limited
- Optional 90° or 20° installation
- Standard 3/4” tapered shaft
- Lock-to-lock steering wheel turns: approx. 3,8
- Stroke: 9” (228 mm)
- Maximum allowable steering wheel diameter: 16” (406 mm)
- Minimum steering cable bend radius: 7.9” (200 mm)
- Minimal feedback
- Compact for mounting
- T71FC steering systems are not to be used on boats equipped with engines
that exceed the maximum horsepower rating of the boat.
- For boats faster than 50 mph the twin cable steering system T72FC is
recommended
- Exceeds EN 28848 safety standards
- Exceeds ABYC P17 safety standards
|
|
500-0844 1310 Spicer Bolt Pattern To Jet Pump Spline
- Overall length: 7-1/2"
- Spline Shaft: 1-3/8"
- Flange Mount: 2" x 2-3/8"
- Spline length is 2" inside coupler
- Uses 3/8-24 bolts
This unit bolts to the PTO flange. This is the most standard u-joint assembly found in production style boats.
Note: The overall length does not include the PTO flange which is and additional one inch thick.
Need help choosing your new driveshaft? Check out this handy tutorial!
|
|
This Part has options, please click the button below to order.
620-103115 "XS" Xtreme Loader Scoop for 12JC, 12JG, 12JI Pumps
The "XS" Xtreme Series Jet Loader Scoop is just that
- Xtreme. It is designed for all out competition in boats
that produce 500+ horsepower. By using an open center
loader style design this loader will jam pack the impeller
virtually pre-loading the pump.
Note: Engines that don't make
500+ horsepower that attempt to use this unit may
actually experience an overloaded jet creating a "bog" type sensation.
|
|