BOWL ASSEMBLY, DOM 10-1/4

Bolt Circle Size: 10-1/4", center to center.

Jet Drive Water Pressure Relief Kit

The kit from Pack-A-Jet will come with a brass pressure relief valve with 1/2" npt bypass outlet and a stainless steel extension tube for easy installation. Direct fit to the Berkeley models 12JC and 12JG with 3/8" NPT water inlet, but can be used on other models as well as long as they have a 3/8"NPT water inlet on the inside of the boat. Will NOT work on 12JE model or similar pumps where the water inlet is on the outside of the boat. In that case you'll want to buy a pressure relief valve only and a simple T fitting to adapt to the existing inlet tube.

The pressure relief valve opens at app. 12 to 15 psi to move excess water overboard.
Optional hose kits are available see related products below.

Berkeley "B" Partial Overhaul Kit

To facilitate easier maintenance of your Berkeley pump, Berkeley Jet Drive has created three `Repair / Parts' Kits Each kit is applicable to all Berkeley Jet Drive Models: 12JB, 12JC, 12JG, 12JE, and 12JF There are many people attempting to sell non-original replacement kits in an attempt to compete price wise They short sell or remove parts to try and compete with factory pricing Don't be mislead, get all that you pay for, demand authentic Berkeley parts!

"B" Partial Overhaul Kit includes:

1 L02850 Intake Gasket 1 S14063 Thrust Bearing 1 S14482 Impeller Key 1 S14475 Bearing Cap Seal 1 S14380 Suction Piece Seal 1 S14476 Bowl Seal 1 S14478 Retaining Ring 1 S09017 Bowl Gasket 1 S10870 Nozzle Hsg. Gasket 1 S09018 Bearing Cap Gasket 1 S10068 Insulator 1 S10125 Wear Ring

2 S14483 Bowl Bearings 1 S13531 Steering Tube Bushing 1 S09488 Grommet 4 S08287 Packing Rings 4 S14477 Nyliner Bearing 2 S15414 Nyliner Bearing 1 S13166 Transom Gasket 1 S13731 Bowl O-Ring 1 S17737 Nozzle O-Ring 1 S13734 Hand Hole Cover O-Ring 1 S12005 Impeller Nut 1 S09850 Bowl Bearing Cap

Berkeley "C" Seals & Gaskets Kit

To facilitate easier maintenance of your Berkeley pump, Berkeley Jet Drive has created three `Repair / Parts' Kits Each kit is applicable to all Berkeley Jet Drive Models: 12JB, 12JC, 12JG, 12JE, and 12JF. There are many people attempting to sell non-original replacement kits in an attempt to compete price wise They short sell or remove parts to try and compete with factory pricing Don't be mislead, get all that you pay for, demand authentic Berkeley parts!

"C" Seals & Gaskets Kit Only includes:

• 1 L02850 Intake Gasket
• 1 S14475 Bearing Cap Seal
• 1 S14380 Suction Piece Seal
• 1 S14476 Bowl Seal
  
• 1 S09017 Bowl Gasket
• 1 S10870 Nozzle Hsg. Gasket
• 1 S09018 Bearing Cap Gasket
• 1 S13531 Steering Tube Bushing
• 1 S09488 Grommet
• 4 S08287 Packing Rings
• 1 S13166 Transom Gasket
• 1 S13731 Bowl O-Ring
• 1 S17737 Nozzle O-Ring
• 1 S13734 Hand Hole Cover O-Ring

New Replacement 12JE Jet Pump Only

DESCRIPTION: The Model 12JE Jet-Drive is constructed of a super-tough, high-strength, aluminum alloy, castings the finest and most serviceable material available. Precision machined and hard-anodized, assembled with stainless steel fasteners, assures maximum performance with a minimum of maintenance. Dissimilar metals are protected from each other by inert insulators to retard corrosion. Using Berkeley's unique single stage, mixed flow, impeller, this unit gives maximum thrust per horsepower. Developed over a period of many years, and field tested, assures the user of the Model 12JE Jet-Drive many years of trouble-free boating. A popular unit with boat manufacturers because of its ease of installation in specially molded hulls.

APPLICATION: Designed for fast, simple installation in specially molded hulls measuring 14 to 24 feet in overall length, with a gross weight of not over 5,000 pounds per unit, including passengers and gear.

FEATURES: No intake adapter or transom housing required for simple bolt in installation in specially molded hulls. Entire unit located outside the hull, saving five inches. Lighter weight, 40 lbs. less than the 12JC. Only one rotating element, the shaft and impeller assembly. A single stage enclosed, mixed flow, impeller available in aluminum or stainless steel, machined to match horsepower involved. Replaceable, insulated impeller wear ring, machined to close tolerances for minimum bypass and high pump efficiency. Strong self-cleaning finger-type intake grate. Readily accessible and serviceable stuffing box-type shaft seal. Heavy duty, grease lubricated, ball-type, thrust bearing isolated and sealed for protection from accidental water damage. Easily accessible, outside the hull, hand hole for impeller clean out in the unlikely event of clogging. Long life, oil lubricated, sleeve-type, tail bearing, sealed from the water. Smooth working steering nozzle and reverse bucket for effortless steering in forward and reverse with low, side-mounted, controls. Nozzle 0 ring seal assures minimum spray. Long blade rudder for positive boat handling at low speeds with no appreciable loss in performance at higher speeds.

POWER REQUIREMENTS: Approximately 10 to 27 pounds gross boat weight requires 1 HP. Higher or lower speeds will be obtained as gross weight varies. Weight distribution, hull length and design are other factors affecting total boat performance. The standard aluminum alloy impeller is used with engines up to 400 HP; over 400 HP, a stainless steel impeller is recommended.

OPTIONAL EQUIPMENT: Stainless steel impeller,  shift-throttle controls, instrument panels, gauge clusters and wiring harnesses, intake fins and transom trim tabs, hull insert or mold plug.

DIMENSIONS / WEIGHT: Net weight approximately 85 pounds. Dimensions may vary and are for estimating only. Refer to catalog installation drawings for complete dimensions.

 

New Complete 12JE Pump With Trimmable Nozzle Assembly

DESCRIPTION: The Model 12JE Jet-Drive is constructed of a super-tough, high-strength, aluminum alloy, castings the finest and most serviceable material available. Precision machined and hard-anodized, assembled with stainless steel fasteners, assures maximum performance with a minimum of maintenance. Dissimilar metals are protected from each other by inert insulators to retard corrosion. Using Berkeley's unique single stage, mixed flow, impeller, this unit gives maximum thrust per horsepower. Developed over a period of many years, and field tested, assures the user of the Model 12JE Jet-Drive many years of trouble-free boating. A popular unit with boat manufacturers because of its ease of installation in specially molded hulls.

APPLICATION: Designed for fast, simple installation in specially molded hulls measuring 14 to 24 feet in overall length, with a gross weight of not over 5,000 pounds per unit, including passengers and gear.

FEATURES: No intake adapter or transom housing required for simple bolt in installation in specially molded hulls. Entire unit located outside the hull, saving five inches. Lighter weight, 40 lbs. less than the 12JC. Only one rotating element, the shaft and impeller assembly. A single stage enclosed, mixed flow, impeller available in aluminum or stainless steel, machined to match horsepower involved. Replaceable, insulated impeller wear ring, machined to close tolerances for minimum bypass and high pump efficiency. Strong self-cleaning finger-type intake grate. Readily accessible and serviceable stuffing box-type shaft seal. Heavy duty, grease lubricated, ball-type, thrust bearing isolated and sealed for protection from accidental water damage. Easily accessible, outside the hull, hand hole for impeller clean out in the unlikely event of clogging. Long life, oil lubricated, sleeve-type, tail bearing, sealed from the water. Smooth working steering nozzle and reverse bucket for effortless steering in forward and reverse with low, side-mounted, controls. Nozzle 0 ring seal assures minimum spray. Long blade rudder for positive boat handling at low speeds with no appreciable loss in performance at higher speeds.

POWER REQUIREMENTS: Approximately 10 to 27 pounds gross boat weight requires 1 HP. Higher or lower speeds will be obtained as gross weight varies. Weight distribution, hull length and design are other factors affecting total boat performance. The standard aluminum alloy impeller is used with engines up to 400 HP; over 400 HP, a stainless steel impeller is recommended.

OPTIONAL EQUIPMENT: Stainless steel impeller,  shift-throttle controls, instrument panels, gauge clusters and wiring harnesses, intake fins and transom trim tabs, hull insert or mold plug.

DIMENSIONS / WEIGHT: Net weight approximately 85 pounds. Dimensions may vary and are for estimating only. Refer to catalog installation drawings for complete dimensions.

 

Aluminum Rudder

If you're looking for some more low-speed maneuverability or improved high-speed tracking then here's your answer Berkeley manufactures two models of bolt-on rudders The first is an entry level economy plastic rudder, while the second is a sturdy cast aluminum version of the same rudder. Note: The plastic unit will not survive in aggressive boating situations If you want durability then you need an aluminum rudder. Rudders sold complete with pin and hardware. NOTE: These only fit stock Berkeley Nozzles, they do not fit any aftermarket trimmable nozzles.

Supersedes: 152-J0595, 152-RK0595

New Replacement 12JG Jet Pump Only

DESCRIPTION: The Model 12JG Jet-Drive is constructed of a super-tough, high-strength, aluminum alloy, castings the finest and most serviceable material available. Precision machined and hard-anodized, assembled with stainless steel fasteners, assures maximum performance with a minimum of maintenance. Dissimilar metals are protected from each other by inert insulators to retard corrosion. Using Berkeley's unique single stage, mixed flow, impeller, this unit gives maximum thrust per horsepower. Divided bowl-steering assembly construction offers the boater the advantage of readily adding accessories to change thrust angle.

APPLICATION: Ideally suited for vee and modified vee hull boats, measuring 14 to 24 feet in overall length, with a gross weight of not over 5,000 pounds per unit, including passengers and gear.

FEATURES: Only one rotating element, the shaft and impeller assembly. Specially designed intake adapter to assure pump alignment and boat bottoms matching for efficient performance. Two transom housings to accommodate transom angles of 0° to 9° and 9° to 18°. A single stage, enclosed, mixed flow, impeller available in aluminum or stainless steel, machined to match horsepower involved. Replaceable, insulated impeller wear ring machined to close tolerances for minimum bypass and high pump efficiency. Strong self-cleaning finger-type intake grate. Readily accessible and serviceable stuffing box-type shaft seal. Heavy duty, grease lubricated, ball-type thrust bearing, isolated and sealed for protection from accidental water damage. Easily accessible hand hole for impeller clean out in the unlikely event of clogging. Cover securely held in place by swing bolts and special wrench, which may be used for stuffing box adjustment. Long life, oil lubricated, sleeve-type, tail bearing, sealed from the water. Smooth working steering nozzle and reverse bucket for effortless steering in forward and reverse. Nozzle O-ring seal assures minimum spray. Long blade rudder for positive boat handling at low speeds with no appreciable loss in performance at higher speeds. Steering assembly is removable from bowl for addition of steering wedge or Droop Snoot.

POWER REQUIREMENTS: Approximately 10 to 27 pounds gross boat weight requires 1 HP. Higher or lower speeds will be obtained as gross weight varies. Weight distribution, hull length and design are other factors affecting total boat performance. The standard aluminum alloy impeller is used with engines up to 400 HP; over 400 HP, a stainless steel impeller is recommended.

OPTIONAL EQUIPMENT: Hand hole extension, stainless steel impeller, shift-throttle controls, instrument panels, gauge clusters and wiring harnesses, steering wedge, Droop Snoot.

DIMENSIONS / WEIGHT: Net weight 125 pounds total unit. Dimensions will vary with different intake and transom adapters and are for estimating only. Refer to catalog installation drawings for complete dimensions.

New Replacement 12JG Jet Pump Only, With Stainless Steel Impeller

DESCRIPTION: The Model 12JG Jet-Drive is constructed of a super-tough, high-strength, aluminum alloy, castings the finest and most serviceable material available. Precision machined and hard-anodized, assembled with stainless steel fasteners, assures maximum performance with a minimum of maintenance. Dissimilar metals are protected from each other by inert insulators to retard corrosion. Using Berkeley's unique single stage, mixed flow, impeller, this unit gives maximum thrust per horsepower. Divided bowl-steering assembly construction offers the boater the advantage of readily adding accessories to change thrust angle.

APPLICATION: Ideally suited for vee and modified vee hull boats, measuring 14 to 24 feet in overall length, with a gross weight of not over 5,000 pounds per unit, including passengers and gear.

FEATURES: Only one rotating element, the shaft and impeller assembly. Specially designed intake adapter to assure pump alignment and boat bottoms matching for efficient performance. Two transom housings to accommodate transom angles of 0° to 9° and 9° to 18°. A single stage, enclosed, mixed flow, impeller available in aluminum or stainless steel, machined to match horsepower involved. Replaceable, insulated impeller wear ring machined to close tolerances for minimum bypass and high pump efficiency. Strong self-cleaning finger-type intake grate. Readily accessible and serviceable stuffing box-type shaft seal. Heavy duty, grease lubricated, ball-type thrust bearing, isolated and sealed for protection from accidental water damage. Easily accessible hand hole for impeller clean out in the unlikely event of clogging. Cover securely held in place by swing bolts and special wrench, which may be used for stuffing box adjustment. Long life, oil lubricated, sleeve-type, tail bearing, sealed from the water. Smooth working steering nozzle and reverse bucket for effortless steering in forward and reverse. Nozzle O-ring seal assures minimum spray. Long blade rudder for positive boat handling at low speeds with no appreciable loss in performance at higher speeds. Steering assembly is removable from bowl for addition of steering wedge or Droop Snoot.

POWER REQUIREMENTS: Approximately 10 to 27 pounds gross boat weight requires 1 HP. Higher or lower speeds will be obtained as gross weight varies. Weight distribution, hull length and design are other factors affecting total boat performance. The standard aluminum alloy impeller is used with engines up to 400 HP; over 400 HP, a stainless steel impeller is recommended.

OPTIONAL EQUIPMENT: Hand hole extension, stainless steel impeller, shift-throttle controls, instrument panels, gauge clusters and wiring harnesses, steering wedge, Droop Snoot.

DIMENSIONS / WEIGHT: Net weight 125 pounds total unit. Dimensions will vary with different intake and transom adapters and are for estimating only. Refer to catalog installation drawings for complete dimensions.

New Complete 12JG Pump with Trim Nozzle

DESCRIPTION: The Model 12JG Jet-Drive is constructed of a super-tough, high-strength, aluminum alloy, castings the finest and most serviceable material available. Precision machined and hard-anodized, assembled with stainless steel fasteners, assures maximum performance with a minimum of maintenance. Dissimilar metals are protected from each other by inert insulators to retard corrosion. Using Berkeley's unique single stage, mixed flow, impeller, this unit gives maximum thrust per horsepower. Divided bowl-steering assembly construction offers the boater the advantage of readily adding accessories to change thrust angle.

APPLICATION: Ideally suited for vee and modified vee hull boats, measuring 14 to 24 feet in overall length, with a gross weight of not over 5,000 pounds per unit, including passengers and gear.

FEATURES: Only one rotating element, the shaft and impeller assembly. Specially designed intake adapter to assure pump alignment and boat bottoms matching for efficient performance. Two transom housings to accommodate transom angles of 0° to 9° and 9° to 18°. A single stage, enclosed, mixed flow, impeller available in aluminum or stainless steel, machined to match horsepower involved. Replaceable, insulated impeller wear ring machined to close tolerances for minimum bypass and high pump efficiency. Strong self-cleaning finger-type intake grate. Readily accessible and serviceable stuffing box-type shaft seal. Heavy duty, grease lubricated, ball-type thrust bearing, isolated and sealed for protection from accidental water damage. Easily accessible hand hole for impeller clean out in the unlikely event of clogging. Cover securely held in place by swing bolts and special wrench, which may be used for stuffing box adjustment. Long life, oil lubricated, sleeve-type, tail bearing, sealed from the water. Smooth working steering nozzle and reverse bucket for effortless steering in forward and reverse. Nozzle O-ring seal assures minimum spray. Long blade rudder for positive boat handling at low speeds with no appreciable loss in performance at higher speeds. Steering assembly is removable from bowl for addition of steering wedge or Droop Snoot.

POWER REQUIREMENTS: Approximately 10 to 27 pounds gross boat weight requires 1 HP. Higher or lower speeds will be obtained as gross weight varies. Weight distribution, hull length and design are other factors affecting total boat performance. The standard aluminum alloy impeller is used with engines up to 400 HP; over 400 HP, a stainless steel impeller is recommended.

OPTIONAL EQUIPMENT: Hand hole extension, stainless steel impeller, shift-throttle controls, instrument panels, gauge clusters and wiring harnesses, steering wedge, Droop Snoot.

DIMENSIONS / WEIGHT: Net weight 125 pounds total unit. Dimensions will vary with different intake and transom adapters and are for estimating only. Refer to catalog installation drawings for complete dimensions.

 

G-Bowl

Supersedes: 152-J0495

To replace a single piece C-Bowl, you will need to purchase this G-Bowl and G Nozzle Housing 150-L-05026 (see related parts) and all necessary gaskets, bolts and pins. See G-Pump breakdown here.